Crestron-electronic QUICK MEDIA DISTRIBUTION CENTER QM-MD4X2 Manuel d'utilisateur

Crestron QM-MD4x2 QuickMedia Distribution Center Operations Guide

QuickMedia Distribution System Crestron QM-MD4x2 QM IN G24 Y Z The MD4x2 contains four QM ports for connecting QM sources. Each QM port has an RJ-4

Crestron QM-MD4x2 QuickMedia Distribution System QM POWER G24 The MD4x2 contains two 2-position terminal block connectors that provide 24VDC power

QuickMedia Distribution System Crestron QM-MD4x2 While in the system mode, pressing V will indicate where the video portion of a signal is routed.

Crestron QM-MD4x2 QuickMedia Distribution System Industry Compliance As of the date of manufacture, the MD4x2 has been tested and found to comply w

QuickMedia Distribution System Crestron QM-MD4x2 each network unit to be daisy-chained must be added together to determine the power factor of the

Crestron QM-MD4x2 QuickMedia Distribution System CRESCAT-QM Cable NOTE: Do not untwist the two wires in a single pair for more than 1/3-1/2” (0.8

QuickMedia Distribution System Crestron QM-MD4x2 The pin assignments for Crescat-QM, CAT5, CAT5E, and CAT 6 wiring are based on the EIA/TIA 568B RJ

Crestron QM-MD4x2 QuickMedia Distribution System control system to recognize a network device via its serial number, which is stored in the device’

QuickMedia Distribution System Crestron QM-MD4x2 “Set Net ID by TSID” Window 5. Enter either the serial number or TSID number of the device that

Crestron QM-MD4x2 QuickMedia Distribution System 3. Enter the serial number or TSID number as instructed; press the appropriate button to obtain t

This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647

QuickMedia Distribution System Crestron QM-MD4x2 4. Repeat procedure (steps 1 through 3) to attach the remaining ear to the opposite side. Stackin

Crestron QM-MD4x2 QuickMedia Distribution System The required 24 VDC power for the QM inputs and QM outputs can be supplied in a variety of ways. T

QuickMedia Distribution System Crestron QM-MD4x2 Earliest Version Software Requirements for the PC NOTE: Crestron recommends that you use the late

Crestron QM-MD4x2 QuickMedia Distribution System Expanded QM-RMCRX System Tree C2Net-Device Slot in Configuration Manager To incorporate an MD4x2

QuickMedia Distribution System Crestron QM-MD4x2 NOTE: This procedure sets the Net ID for the MD4x2 in the program only. It does not automatically

Crestron QM-MD4x2 QuickMedia Distribution System QM-MD4x2 Analog Input Signal Descriptions INPUT DESCRIPTION VideoOut1 and VideoOut2 Select the QM

QuickMedia Distribution System Crestron QM-MD4x2 QM-MD4x2 Digital Output Signal Descriptions OUTPUT DESCRIPTION LocalMode-FB Indicates that the MD

Crestron QM-MD4x2 QuickMedia Distribution System Uploading and Upgrading Assuming a PC is properly connected to the entire system, Crestron program

QuickMedia Distribution System Crestron QM-MD4x2 Typical Connection Diagram when Uploading 1. Open the Crestron Viewport. Either launch the stand

Crestron QM-MD4x2 QuickMedia Distribution System “Port Settings” Window NOTE: The parameters shown in the illustration above are the port settings

Crestron QM-MD4x2 QuickMedia Distribution System Contents QuickMedia Distribution System: QM-MD4x2 1 Introduction ...

QuickMedia Distribution System Crestron QM-MD4x2 File Transfer | Send Program Command 3. The “Send Program” window appears, as shown after this s

Crestron QM-MD4x2 QuickMedia Distribution System 2. As shown after this step, select File Transfer | Update Network Device Firmware… from the View

QuickMedia Distribution System Crestron QM-MD4x2 Operation Operating Modes The MD4x2 operates in either the system mode or the local mode. When ope

Crestron QM-MD4x2 QuickMedia Distribution System 3. Select the input to be switched by pressing its corresponding button. 4. Select the destinati

QuickMedia Distribution System Crestron QM-MD4x2 Problem Solving Troubleshooting The following table provides corrective action for possible troubl

Crestron QM-MD4x2 QuickMedia Distribution System Future Updates As Crestron improves functions, adds new features, and extends the capabilities of

QuickMedia Distribution System Crestron QM-MD4x2 Appendix: Serial Protocol All commands and responses are printable ASCII and are terminated with

Crestron QM-MD4x2 QuickMedia Distribution System NOTE: The setting for the verbose mode is retained even after power to the MD4x2 is cycled. NOTE:

QuickMedia Distribution System Crestron QM-MD4x2 When the verbose mode is on and the routing status changes while the MD4x2 is in the system mode,

Crestron QM-MD4x2 QuickMedia Distribution System Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be return

Crestron Electronics, Inc. Operations Guide – DOC. 6278 15 Volvo Drive Rockleigh, NJ 07647 06.04 Tel: 888.CRESTRON Fax: 201.767.7576 Specif

Crestron QM-MD4x2 QuickMedia Distribution System QuickMedia Distribution System: QM-MD4x2 Introduction Features and Functions The Crestron® QuickMe

QuickMedia Distribution System Crestron QM-MD4x2 Applications The MD4x2 is part of the Crestron MediaManager line of integrated presentation soluti

Crestron QM-MD4x2 QuickMedia Distribution System Functional Diagram of the QM-MD4x2 VIDEO4 X 2 X 5MUXDIGITALAUDIO4 X 2 X 1MUXQMFront End1QMFront En

QuickMedia Distribution System Crestron QM-MD4x2 Specifications Specifications for the QM-MD4x2 are listed in the following table. QM-MD4x2 Specif

Crestron QM-MD4x2 QuickMedia Distribution System QM-MD4x2 Physical View (Front) QM-MD4x2 Physical View (Rear) QM-MD4x2 Physical Views 17.03 in(43