Crestron-electronic CEN-iServer Manuel d'utilisateur Page 18
- Page / 32
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Crestron iServer™ Network Audio Server Crestron CEN-ISERVER
Installation
Rack Mounting
The CEN-ISERVER can be mounted in a rack or stacked with other equipment. Two
“ears” are provided with the CEN-ISERVER so that the unit can be rack mounted.
These ears must be installed prior to mounting. Complete the following procedure to
attach the ears to the unit. The only tool required is a #2 Phillips screwdriver.
WARNING: To prevent bodily injury when mounting or servicing this unit in a
rack, take special precautions to ensure that the system remains stable. The following
guidelines are provided to ensure your safety:
• When mounting this unit in a partially filled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
NOTE: If rack mounting is not required, rubber feet are provided for tabletop
mounting or stacking. Apply the feet near the corner edges on the underside of the
unit.
NOTE: Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct
connections to the branch circuit (e.g. use of power strips).
To install the ears:
1. There are screws that secure each side of the CEN-ISERVER top cover.
Using a #2 Phillips screwdriver, remove the three screws closest to the front
panel from one side of the unit. Refer to the diagram following step 3 for a
detailed view.
2. Position a rack ear so that its mounting holes align with the holes vacated
by the screws in step 1.
3. Secure the ear to the unit with three screws from step 1, as shown in the
following diagram.
Ear Attachment for Rack Mounting (this image shows a 1RU device)
USE COVER SCREWS
4. Repeat procedure (steps 1 through 3) to attach the remaining ear to the
opposite side.
Stacking
Four “feet” are provided with the CEN-ISERVER so that if the unit is not rack
mounted, the rubber feet can provide stability when the unit is placed on a flat
surface or stacked. These feet should be attached prior to the hookup procedure.
NOTE: No more than two CEN-ISERVER units should be stacked.
10 • Crestron iServer™ Network Audio Server: CEN-ISERVER Operations Guide – DOC. 6759B
- Crestron CEN-ISERVER 1
- Operations Guide 1
- Contents 3
- CEN-ISERVER Quick Start 5
- USE COVER SCREWS 6
- Connect the iPod 7
- Server: CEN-ISERVER 9
- Applications 10
- Specifications 11
- Physical Description 12
- 1 TX + 5 N/C 14
- 2 TX - 6 RC 14
- 3 RC+ 7 N/C 14
- 4 N/C 8 N/C 14
- Industry Compliance 16
- Network Wiring 17
- CAT5 Wiring 17
- Identity Code 17
- Installation 18
- Hardware Hookup 19
- LOCKING SCREW 20
- Programming Software 23
- C2ENET-1 Device, Slot 8 24
- Example Program 25
- Uploading and Upgrading 26
- Programs and Firmware 27
- Program Checks 27
- Problem Solving 28
- Reference Documents 29
- Further Inquiries 29
- Future Updates 29
- Return and Warranty Policies 30
Sony PCV-RZ422P manuály
Uživatelské manuály a uživatelské příručky pro ne Sony PCV-RZ422P.
Poskytujeme 2 manuály pdf Sony PCV-RZ422P ke stažení zdarma podle typů dokumentů: Technické informace
Commentaires sur ces manuels